Instant Help by ProAction Networks |
The command you need to look at is:
ACPDN / ACPKN / AKYD
For the new extension you need to assign it into the correct Pickup
up.
Under CPG (should be blank one) put the relevant value (1-5) as per
below:
CPG 1 / 7= Reception
CPG 2 / 8= Clerks
CPG...
There's no IP addresses configured by default.
Have to login as:
U: SV9500user
P: P@ssw0rd
Then type: config_tool.sh
& use same password as above.
Once licenses have been added
On dual CPU with dual serial and compact flash cards, used CMOD to
switch between active CPUs.
Browse to the main system IP and upload the new SVI file
Enter PCPro command CFCS and press Execute button, to effectuate th...
FKY 21 is a cancel / flash function
FKY 59 is a release function
You need to set ADSL SKP0 5 and 15 to include 21 and 59 so that when
mid-transfer (consultation hold) you have the option to cancel the
transfer or disconnect (complete the transfer).
...
You need to login using usrConsole
setup sp to run through the setup of the card
at the end of the setup do 'setup one' to setup the one time password
ASECL to setup the one time password on the PBX (can be infinite)
Data memory backup is recommen...
ACCTN you create a CCTN e.g.1
ACCDN you assign a specific route to a CCT
ASYDL you must switch Sys 1 / 1088 / B5 to 1.
More to follow...
Always use ALGSN and do a 1-1 map for extensions.
You have RFC 0-15 for barring.
ARSC/ARSCN
Lookup route for barring on and then you see the RSC along the top
(RSC is set on the phone)
Always use RRI-3 for terminals. Other RRIs are for consoles etc.
0 bars everything going over it (usually for ho...
Benoy Newark Main 01636672356
London 0
Holmes Wood 550
*25 switches between day and nite mode.
Control of CLI at Bonhams is done on a number of levels.
Route Programming of ISDN30 routes dictate that if a extension has a
DDI number, it will use those last 6 digits as the outbound CLI over
that ISDN trunk. The number must be a DDI assigned on the ...
Location Index 1: NBS
Radios Allocated: 70
Subnet:10.43.0.0
Decimal Range:10-80
RPN HEX Range:010-04F
Location Index 2: KB
Radios Allocated: 20
Subnet:10.43.6.0
Decimal Range: 080-099
RPN HEX Range:050-063
Location Index 3: Edinburgh
...
Manchester 273822 -> 2920 -> (direct to Linda)
Tetbury 502200 -> 2910 (direct to extension)
Leeds 345755 -> 2980 (direct to Alison)
Chester 313936 -> 2930 ( Chester virtual ring group)
LA has an example of how to manipulate the trunk used on an SBC based
on the MAID. In this example, we have:
MAID 0005 - the standard LA MAID which strips the leading 9 dialled
by the user and sends the call to LA SBC first.
MAID 0015 - the non standard ...
NYC: http://10.3.210.56
LA/SF : http://10.3.214.56
Logins are:
elmar / pr0action
stella / pr0action
Prerequisites:
Clients require Microsoft DotNet 3.5 installed, which is seperate from
4.0 or 4.5. WINDOWS 7 OR LATER WILL ALREADY WILL HAVE THIS...
Set Softkey data ADSL
Change Softkey words: AFDD
Need doing
SS
Motorbodies
Atkin x 2
Don't
VillaPlus
St Anns
Essex
ALOCL put network into a location
AIVCL Location 1/1
0 - Default
1 - Slough - 10.43.12.0
2 - Elemis - 10.43.2.0
3 - KB - 10.43.6.0
4 - NBS 10.43.0.0
5 - PR - 10.43.6.0
6 - 10.43.122.0
7 - 10.43.71.0
8 - 10.43.50.0
10 - NYC 10.3.210.0...
AUACN can determine specific ways a SIP handler phone will work.
dR4WHie5SEGdxj+WTpgGcNASt3j5oynzqhG0BLC8hbJGL+R3pa8GEDhtzML9iMObega86bo1qo83T9Zpkv25FErOYJkvJ/OblH5pxAjbZaL84zG7vNifJfU/tpxESTsNZ1FajG/SnEkOrHFSUAqHHUb9vql/x1VE6qb0uBh3gjUZljrh3Kqf74hLF6fyiXO5QCqDZK6tcWtu+4CZRQ9qAHOKoHXpgz5QAnnptb9NroVLXw0wLbOmYjKpIx2Flfl...
ARTD used for trunk config
DC is set to 6 digits so it will expect 6 from BT and send 6 to BT.
ARTI used for ISDN trunk config
34)NPI and 85)ADRSing should be enabled to send the CLI from ACDDN
84)CLOP is used for using a few other commands to app...
RBRservice / R3db0x123!
admin / recorder
Setup / Misc
When all extensions are learned, uncheck the 'channel detection mode'
to stop learning new numbers added to the disabled list.
Searching Records
Internal extensions will need a wildcard of % ...
Follow this guide, except replace the vib file with
"lsi-mr3-6.912.12.00-1OEM.550.0.0.1391871.x86_64.vib" which i've saved
in the ISOs folder.
https://serenity-networks.com/how-to-install-lsi-megaraid-storage-manager-msm-on-vmware-esxi-5-5/
[https://ser...
Notes
* Calls from SBC SIP Endpoints going to 3xx pass over the E1 link,
which mean when they enter the NEC system they first have to follow
the DDI routing plan. So don't assuming ringing 300 from the SBC
reaches extension 300 - it first goes to the ...
ISDN30 card is using 00-60-b9-e2-f6-1a
ISDN30 route 10 uses trunks 001000 - 001037
VS32 is 00-60-b9-ff-39-57
Uses LENS 001080 and 001100.
To interrupt Centos boot into single user and update root password:
Hold shift on boot.
Press a then put ...
Loading Dock is 4014 which AHLS rings 1309
1309 has been added to:
Collections phone is 4310 and ASHL rings 4604
MAID settings
AFRSN
TN1, LGRT1 NPC is the number dialled. Try 9 followed by the MAID of
0000-9999. You'll see the OPR for route selection and the name of the
MAID area.
AOPRN
TDPN is 0, OPR is the OPR used by the MAID and RA is the route advance
n...
You can change ASYDL 1, 830 b7 from 1 to a 0 and this should enable
just holding tone instead of MOH source of VS32
AAEDL selects the type of WAV file played by the VS32.
Selected Equipment kind: VS
TN 1 and EQP 64
Multiple Conneciton is set to Si...
There's no IP addresses configured by default.
Have to login as:
U: SV9500user
P: P@ssw0rd
Then type:
& use same password as above.
1) Remember you need a newer copy of PC Pro to accompany the newer
release (with new commands)
2) You don't need to copy anything to the datastore because you're
going to deploy it as a new OVF template.
3) Be careful that if you connect it's network ...
he Login page, type the user name and password. If you are using the
IMM for the first time, you can obtain the user name and password from
your system administrator. All login attempts are documented in the
system-event log.
Note: The IMM is set initia...
ARTD or LRTD shows all the route class data per route. If you look up
an existing ISDN30 you'll see all the standard settings.
DC is important as it's the digits recieved by the PSTN - so if
Openreach are sending 3 digits it needs to be reduced to 3 fol...
Good notes:
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
Note that on the Sonicwall, I had to re-route the 6 NAT forwarders to
the UC540 and also under...
ADSL / LDSL shows the keys depending on the state of the phone:
0: idle
1:ringing
2:ringing
4:talking
Bonhams:
128 / 34: in
129 / 35: meet
130 / 36: out
131 / 37: leave
192 / 38: record
193 / 39: login
194 / 40: divert to vm
195 ...
PREREQUISITES
You need to know how to navigate MOC mode.
You need to know the last 3/6 digits of the DDI you wish to
check/amend.
Nearly all NEC systems remain in DAY mode all the time. However there
is a command to switch all the DDI routes from DA...
Crossover blue and orange
NEC way of specifying multiple SIP servers using linux DHCP is as
follows:
Specify the sip-servers parameter:
OPTION SIP-SERVERS CODE 120 = STRING;
Specify priority of servers 1,2,3,4, in hex, in double figures and
separated with : - Primary SIP ser...
Make sure the SIP Server is trusted.
On the SIP-128,
set cdn_pattern as 2 (userinfo)
set the cpn_pattern as 1 (userinfo)
Website: proactionnetworks.com
Admin: proactionnetworks.com/administrator - Login solidpro/R0adm0123!
The overall template is called Sirus and a basic guide is here:
https://www.joomlaxtc.com/support/template/templates/sirus-template-guide
Experience 1:...
10.44.199.30 primary
10.44.198.30 secondary
ASYDN 1199 B1 - 1=RBT, 0=MOH. Would be worth trying to see if this
changes it.
You need one extension programmed under AISTL, on a LEN with the mac
address assigned and the type as TEC3 and SIP-MC8 extension.
You need to check the one time password is allowed once ASECL
Also check the card is not already in the trusted list.
Split files are smaller and quicker but not for older phones
Combined files are larger and do support older phones.
FTP username is alex / alex
FTP address is 192.168.200.250
2345-17960-001.sip.ld SIP application executable for VVX 1500
FTP sett...
PURE IP UDP VOIP PLATFORM DETAILS:
California VoIP Platform
SIP + Media IP Address: 209.118.186.30
SIP Port: 5060
SIP Protocol: UDP
Pure IP Media Ports: 16384 - 17584
Media Protocol: UDP (RTP)
New York VoIP Platform
SIP + Media IP Address:...
Point a browser to the IP:9801 and then login using admin/admin and
you'll be able to shut down via the web interface.
Stuart has dumped a load of documentation on the NYC server - QQs
quick questions
To get IE working you have to Add to trusted sites and enable some
kind of active X
Quantify Login is admin / recorder
LTR folder
Added a local account called RBRSer...
SL-29-UC-K9
CISCO2921-V/K9
Max on 2951 is 150 CME and 250 SRST
show license udi
show license feature
show license call-home pak
u:Atmos
p: Atm05Adm1n
WG 217.179.202.149
GB1: 172.16.48.10
ISM: 172.16.48.11
Windows password l0c41
Equ...
Server is called Voicemail.
Username is administrator
Password is : PassMENow!
Then navigate to storefront.sequel.com
Once logged in - click on Office Desktops
You should then be able to use remote desktop connection to connect to
the Voicemail Serv...
4.2. Inbound Calls have no audio or one way audio
Problem Description Inbound calls can be setup to the UC500 but the
calls have no audio or one way audio.
This is usually seen when an external firewall and / or NAT router is
deployed in front of the ...
Note you don't use trunk groups.
Note, the default gateway has to get to the internet somehow. Easiest
is to point the following command to the DG on the interface facing
the main internal LAN:
ip route 0.0.0.0 0.0.0.0 192.168.200.254
The Dial Peer ...
We have
* 89.145.215.51 - going to NEC and Exchange Server 192.168.200.215 /
192.168.200.202
* 77.44.4.169 - going to VM running Server 2016+Exchange
192.168.200.214
* 77.44.4.170 - going to Sonus SBC 1k on 192.168.200.2
* 77.44.4.171
* 77.44....
Some notes:
ASYDL / Sys1 / 852 / b5 = 1 to automatically switch
Note that IPDECT phones should have the multiple gatekeepers,
including the main SV9500 and all the SRMGC nodes in the gatekeeper
list under IP Settings / PBX IP Configuration.
Under System ...
ARSC / ARSCN
Restriction class
Always use RRI3 - thats used by stations. 2 tells to look at toll
restriction.
0 = internal only
ATDP / ATDPN
RSC 2 = OG RT all routes
DC inspection - always include the prefix, eg 909 for 9 then premium
ASYDL 1,831 b0=1
AMAA -> set individual phone into maids
AMAA -> set for network address (time updates straight away on phone
when this is set)
AMAIL/AMAIN
When it's spring, the USA usually comes forward 1 hour a few weeks
before the UK, so you hav...
List of Ring Information
0 NO (No Ringing) No Ringing
1 YES (Ringing) No Ringing 0 seconds
2 NO (No Ringing) Ringing 0 seconds
3 Not used Not used
4 YES (Ringing) Ringing 30 seconds
5 YES (Ringing) Ringing 20 seconds
6 YES (Ringing) Ringing 10 seconds
7 ...
Different types of dialling after 9:
AMNDN
FOR MAID 0004 (NYC):
91 = 12
901 = 17
FOR MAID 0005 (LA):
91 = 12
901 = 17
FOR MAID 0015 (LA BIDS ISDN FIRST):
91 = 12
901 = 17
AFRSN
Calling Beijing on 90118613439268961
ASYDL SYS1 Index 869 b6 to 1 Monitor Function - it is recommended that
this is turned on when bit 7 is ON (see ASYDL SYS1, Index 869, b7 to 1
below)
ASYDL SYS1 Index 869 b7 to 1 Monitor Function for Dterm IP-LAN
For TEC 26 stations, it is necessary to pro...
ASYDL 996 b5 - 0 = disable
ASYDL 831 b5 - it *says* 1 is to disable, but I think it's 0. I've
changed it to 0 09/04/18
On MG/MC SET WARNING_TONE should be disabled.
On phone menu, Audio Settings, 1, 8 RTP alarm, 3 OFF
ARRCN
ARRC
* Use ASDT to program CTI Server queues as virtual numbers in the
PBX.
* Use AMNO to program an underlying OAI monitored pilot (referred to
in Administrator as the underlying System Queue) for each CTI Server
queue except the Hold and Operator queues,...
Use ADTM to enable the FTP service
Visit http://10.43.12.20/mainte [http://10.43.12.20/mainte]
Login is admin and pass is mainte
Here you can upload firmware which is hosted on the PBX and decide
when it is cascaded out to handsets.
If you enable ASYDL 686 b4 change to 1. then enable ASFC 136 to 1 the
headset should go automaticall back on hook when you hangup a call on
SV9500.
VMTOOLS INSTALL ON CENTOS SV9500 VIRTUAL: (THIS IS REQUIRED TO SYNC
THE TIME OF THE PABX TO THE ESXi HOST)
1. On ESXi Hypervisor install VMTools on each SV9500 Guest (CCN/RNs
etc) -> Double click each host. When the window pops up select "Guest
-> Insta...
LEN/IP at BON is 001080 / 10.43.12.16
Open telnet with ATUD
usrConsole to logon.
Setup TP or Setup SP is the common setup commands.
Check ONLINE Lamp is lit.
ASECL to assign MAC to LENS
The lamps for CONF, ANNC, MOH will flash if not set up. T...
Windows 7 Professional Service Pack 1
Product Part No.: X15-37341
Installed from 'OEM' media.
Product ID: 00371-OEM-9319076-02984 match to CD Key data
CD Key: Q9CKD-3V7DJ-7VJ4Y-KC2YK-V467T
Windows Server 2008 R2 Enterprise and Standard
Download:
h...
[HKEY_LOCAL_MACHINESOFTWAREZeacomtspconfiguration]
"Ignore"=dword:42424242 in hexidecimal
Australian interface. Nec PBX
|
|
ProAction Networks Support Desk